Search
Air/Fluid Actuated PTO SPF 600 Specifications
Dimensions |
|||
| A | 11.31 in 287.2 mm |
F |
1.97 in
50 mm
|
|
B
|
8.69 in
220.6 mm
|
G
|
.28 in
7.1 mm
|
|
C
|
7.87 in
200 mm
|
H
|
3/8-16
|
|
D
|
8.50 in
215.9 mm
|
J
|
6.25 in
158.8 mm
|
|
E
|
5.00 in
126.9 mm
|
K
|
8.07 in
205 mm
|
Note: The torque capacity of the clutch is directly proportional to the operating pressure. Maintaining the lowest pressure possible to transfer the desired torque will enable the clutch to run cooler and extend the life span of the internal bearings. The output end of the clutch (female spline/bore) is not capable of supporting any side load. Use overhung load adapters.Drive shaft alignment must be within 3 degrees. Maximum installation angle should be 7°.
PTO SPF 600 Specifications
| U.S | S.I. | |
|---|---|---|
| *Rated Torque (Maximum) | 600 Ft/Lbs | 813 Nm |
| Maximum HP | 342 HP | 255 KW |
| *Maximum RPM | 3000 RPM | 3000 RPM |
| **Maximum Engagement RPM | 1800 RPM | 1800 RPM |
| Rotation | Bi-rotation | Bi-rotation |
| Maximum Actuation Pressure | 140 psi | 9.7 Bar |
| Displacement (Maximum) | 5.2 in3 | 85 cm3 |
| Minimum Flow Rate Required | 1.5 GPM | 5.6 Liters/min |
| Operating Media at Clutch (Oil or Air) | Standard | Standard |
| Maximum Back Pressure to Tank | 7 psi | 0.5 Bar |
| Maximum Fluid Temperature | 200º F | 93º C |
| Material - Output Hub | Alloy Steel | Alloy Steel |
| Material - Housing | Aluminum | Aluminum |
| External Finish - Output Hub | Alloy Steel | Alloy Steel |
| External Finish - Housing | Aluminum | Aluminum |
| Weight (Approximate) | 47 Lbs | 20 Kg |
* Consult Logan Clutch for applications that require lower actuation pressure or increased torque and rpm requirements or greater installation angle.
** SOFTSTART™ feature may be required for engagement above machine idle rpm.
- Input drive flange bolt pattern are dimensioned to correlate with Lovejoy or Centa torsional coupling size 80.
PTO SPF 600 Series Static Torque Ratings
PSI (Ratings in ft. lbs.) |
|||
|---|---|---|---|
| Model SPF 600 |
100 | 120 | 140 |
| 741 | 912 | 1084 | |
PTO SPF 600 Series Static Torque Ratings
BAR (Ratings in Nm) |
|||
|---|---|---|---|
| Model SPF 600 |
6.9 | 8.3 | 9.7 |
| 1005 | 1237 | 1470 | |
Horsepower Required to Drive Hydraulic Pump
| HP* | 87 | 109 | 131 |
|---|---|---|---|
| Pump Size (GPM) |
80 | 100 | 120 |
*HP = PSI x GPM/1371.2 (1714x80% efficiency=1371.2)
*1 HP is required for each 1 GPM@ 1500 PSI
PTO SPF 600 Series Pump Shaft Options
Output Description |
|---|
| SAE 'C' Spline 14t 12/24 DP |
| SAE 'C' Straight Shaft 1.250 Dia. w/5/16 Key |